|
|
 |
 |
|
home /
Instructions / Crowderframe 'C' Sliding Door Pocket
|
|
|
|
|
Crowderframe 'C' Sliding Door Pocket
|
C411 SPINWHEEL HANGER
Crowder frames are the answer where space is limited or where the swinging of hinged door is undesirable or inconvenient. Can be installed in one continuos piece for single or bi-parting doors.
View Crowderframe "C" Sliding Door Pocket Detail
NEW!
Stronger - extruded - aluminum - combination track and header (2) eliminates warpage and reduces deflection.
TYPE 'C' SECTION AND HEAD WITH C-411 HANGER "Spinwheel" quick release type hanger.
SECTION AND HEAD
1" X 3" wood strips (6) fasten to side of header (2) to form a channel over the opening.
Heavy gauge steel uprights (4) come with wood inserts (5). Uprights (4) interlock with steel brackets (3) fastened to the floor. Slotted sections face the door opening for fastening of split jamb and trim.
INSTALLATION INSTRUCTIONS
1. LOCATE HEADER BRACKET AS PER CHART "A" FIGURE 6.
2. CUT ALUMINUM HEADER TO LENGTH (ROUGH OPENING LESS ½").
NOTE: DOOR HANGERS MUST BE INSTALLED IN TRACK PRIOR TO INSTALLING HEADER. HANGER STUD SCREWS SHOULD FACE SAME SIDE OF DOOR. SEE FIGURE 5. INSTALL AND SECURE HEADER TO BRACKET WITH SELF DRILLING "TEK" SCREW. SEE FIGURE 2.
3 LOCATE FLOOR BRACKETS FOR STEEL UPRIGHTS, AS PER CHART "B". SEE FIGURES 4 &
6.
4. LOCATE STEEL UPRIGHTS SECURELY ONTO FLOOR BRACKETS. SEE FIGURE 4. PLUMB AND FASTEN TO ALUMINUM HEADER AT SCREW LINE WITH LOCK WASHER AND "TEK" SCREW AS PER FIGURE 3.
5. CUT 1 X 3 WOOD STRIPS LENGTH TO MATCH DOOR WIDTH AND FASTEN TO HEADER. SEE FIGURE 1.
6. LOCATE HANGER TOP PLATES ON DOOR. SEE FIGURE 5. THREAD HEX NUT ONTO "T" BOLT, SLIDE "SPINWHEEL" NUT UNDER TOP PLATE AND THREAD "T" BOLT INTO "SPINWHEEL". RAISE DOOR AND SLIDE "T" BOLT INTO SLOT ON HANGER BODY. ROTATE "SPINWHEEL" TO ADJUST HEIGHT AND PLUMB AND SECURE SETTING BY LOCKING HEX NUT AGAINST TOP PLATE.
***NOTES: 1. THE SERIES C-411 SPINWHELL HANGERS INCLUDED IN THIS KIT ALLOW FOR
APPROX. 7/8" VERTICAL ADJUSTMENT.
2. A MINIMUM CLEARANCE OF ½" IS REQUIRED BETWEEN DOOR AND FASCIA
TO PERMIT DISENGAGEMENT.
View Chart Figure
CHART A
BRACKET HEIGHT
SET TOP OF BRACKET AT FOLLOWING DIMENSIONS, ALLOWING ½" CLEARANCE TO FLOOR.
|
DOOR HEIGHT
6' - 8"
6' - 10"
7' - 0"
|
|
BRACKET HEIGHT
85"
87"
89"
|
CHART B
FLOOR BRACKETS
|
DOOR WIDTH
2' - 0"
2' - 2"
2' - 4"
2' - 6"
2' - 8"
2' - 10"
3' - 0"
|
DIMENSION A
2' - 0"
2' - 2"
2' - 4"
2' - 6"
2' - 8"
2' - 10"
3' - 0"
|
DIMENSION B
1' - 0"
1' - 1"
1' - 2"
1' - 3"
1' - 4"
1' - 5"
1' - 6"
|
|
|